Contributor

 • 

1 Message

Saturday, July 26th, 2014 5:04 PM

uverse point anywhere remote

Hi,

 

Ive got a uverse STB and TV in the bedroom and the IR on the remote works the TV functions just fine but the STB seemed to be struggling to get the signal from about 18 feet. I bought the Point Anywhere Remote with the hope of solving the problem. Unfortunately, it still performs the same way. No problem with the TV getting the signal but the STB won't pick it up without my walking to the foot of the bed to change the channel.  Am I doing something wrong?

Expert

 • 

3.2K Messages

11 years ago

chicago820 - No, you are not at fault. The PA remote is way under powered.

 

The first thing to do is change the batteries. The PA remote is way more reactive to the slightest drop in battery power than the IR remote. Why are you using it if the STB is not hidden? Use an IR remote.

 

The second item is improving the IR with an antenna.

 

Instead of moving closer hold the remote long side vertical & touch the top end to your chin. Using your head as an antenna.

 

You can get an antenna intended for cell phones to go in the battery compartment or apply an antenna to the dongle. Details below.

 

If you start spending money, get a good IR remote. If your STB is hidden and/or you just want the point anywhere feature, get a Logitech Harmony Smart Control ( https://forums.att.com/t5/Using-your-U-verse-TV-Remote/Logitech-Harmony-Smart-Control-Remote/m-p/4033784#M2997). It is awesome. It is point anywhere & the IR is rock solid with u-verse - every button press works & works right.

 

 

IR Issues

 

Going back 5-6 years there are many posts about IR interference. Remedies included taping over the  IR sensor, hiding the STB, turning off auto brightness on the TV.

 

A common fault was the info button press corrupting to an  STB mute action. The number of reports of this have totally fallen away. My personal initial primary problem was getting the zero to register. But, one day long ago that just went away.

 

Niles Audio Corp. makes IR repeaters & has a video on their web site showing the fragility of the IR coding that is used for U-verse & other boxes.  They said their new line of repeaters could handle it. Oddly, a U-verse customer posted in this community  that they had a NIles install that was not working & after they contacted Niles they did not get any satisfactory resolution.

 

I came to believe that the IR sensor is too sensitive, That the DVR is worse than other STBs. That command type buttons are worse than the number buttons. That, somehow software updates can make it better or worse, So, it is a moving target. Hard to pin down.

 

I noticed that the U-verse remote does work better than my Logitech Harmony model 700. I looked at the IR signal through a digital camera. It appeared to me that the Harmony IR signal is stronger than the U-verse remote. This reinforces my theory that the IR sensor is too sensitive.

 

Recently, my most common problem was FF and Play Buttons often corrupted to chan up and chan down more than six times a night while watching recorded shows, exclusively.

 

I happened to notice that I had a specific kind of "duct tape" covering the blue light on the STB. Actually, it just looks like duct tape, but is electrical tape available at the Home Depot in the electrical dept. - http://www.homedepot.com/p/Commercial-Electric-2-in-x-150-ft-Vinyl-Electrical-Bundling-Tape-Silver-30002664/202741845#specifications

 

This tape has a degree of transparency. I thought I would use it to cover the IR sensor. The remote has never worked better.  In over 100 evenings since I applied the tape - watching recordings while FF through the ads - I have not had one chan up - chan down corruption .  Previously, there would have been at least 6x100=600 occurrences.

 

Almost all button  presses are accepted & none are changed to a different action.

 

 

RF Issues

 

It should not be a surprise, but it is, that half the problems with the RF remote are IR. I run an STB well hidden for a second TV. I had the IR sensor covered with black tape. I replaced the black tape with the "duct tape" & saw an immediate improvement in response to menu buttons. The number buttons were already good - see below for that solution.

 

The STB using RF must be hidden due to the dongle conversion of RF to IR. If it is not hidden it is subject to the following problems:

 

IR corruption - Ironically, the RF remote was often offered as a resolution for IR problems. But, if the STB is not hidden nothing has changed to eliminate theI IR corruption problem. If the corrupting light can be seen by the STB IR sensor it will continue to corrupt the IR signal.

 

If the STB IR sensor can see IR from another remote, it will respond to it.

 

If another STB can see the IR generated by the dongle, it will respond to it.

 

Note that hidden means the IR does not see outside light - If you have an optical repeater(like the Niles mentioned above) it is IR subject to corruption. If you have an IR receiver that produces RF to go through a wall, it is still IR subject to corruption. Any optical link open to the room is still open to IR corruption.

 

Only if the remote is RF (like the point anywhere remote) transmitted to a well hidden device will it ward off IR corruption. The ultimate solution is a wireless remote app. These are available, but incomplete & other devices do not yet support wireless remote. But, the Buddy TV remote can be used for a u-verse STB.

 

Previously, I found the RF remote lacking in RF power -  in the same room, twelve feet away, hidden only by a thin sheet of cardboard.  One method to increase RF power is to hold the remote under your chin while pressing a button - using your head as an antenna.

 

A better way is this antenna placed in the battery compartment - http://www.amazon.com/Cellular-Innovations-A-BOOSTER-Universal-Antenna/dp/B00009WCAP/ref=sr_1_8?ie=UTF8&qid=1366128630&sr=8-8&keywords=cell+phone+booster

 

With this antenna, the channel numbers are almost always accepted. With the "duct tape" in place, the other buttons work almost every time. The remote now works better than ever.

 

But, recently, I discovered that weakened batteries triggers poor results due to low power. If the remote starts acting up go for fresh batteries.  Before I realized the batteries were low I was getting better RF by holding it against a metal arm of a reading light.

 

To increase RF sensitivity - Cut off the base and one leg of a wire coat hanger (one piece). Hold the short leg perpendicular to the dongle and wrap the longer end around the dongle a few turns until the two perpendicular ends are about the same length  (about 3”). Cut the longer one to the same length as the shorter one. If you have an old single "rabbit ear" antenna that used to come with TVs you can wrap the end wire around the dongle.

 

STB Issues

 

Once IR and RF issues are resolved, there are timing issues with the STB to contend with. Numbers process fast and Menu items process slow. You need quick, light  touch on some numbers to avoid duplicates and a slow, strong press on menu activities. Effort is required to  suppress the urge to press again while waiting for a response. It takes concentration to get effective results. Frequently a second press immediately cancels a slow responding first press. Current IR and RF issues amplify the effect of the timing issue.


NEED HELP?